Post by Twisted Metal Video Production on Jul 1, 2012 20:48:02 GMT -5
Giles County Tn Fair Derby Will Be on August 15th.
1st place pays $1200
2nd place pays $600
Heats pay $300 (car count depends on how its split 2 or 3 ways)
Rules Are as Such..........
1.Car entries are to be 1980 and Newer.No Trucks.Cars are to be stock unless otherwise Noted.All Glass,Trim,Fiberglass,Plastic,and Car Interior must be Removed.
2. Doors have the option to be welded,chained,or wired shut,if welded a maximum of 12 inches in length total. If Chained or wired,a maximum of 2 places per door. If welded,Material if not to exceed 1/8 thick x 2 inch wide strap or 3/8 solid rod.
3.For Driver safety a cage is optional but is not mandatory.Cage is not to exceed a 4 point cage(Driver and Passenger door bar,Dash Bar ,and Seat bar) cage material should not be exceed 4-inch tubing or I-Beam.Cage cannot be welded or bolted to frame,only attached to the body of the car.Door bars cannot extend more than 8-inches past the "front door" jam seam toward the rear of the vehicle and cannot extend 8-inches forward "front door" jam seam. Must Be atleast 10 inches off the floor pan. A roll over bar is allowed,Must be Attached to the Cage.
4.Trunk and Hood must be open for inspection.Hood and Trunk maybe secured closed using 4 extra points.Al-thread maybe used in the front(radiator support) and rear 2 body bushings(closest to Bumper) as attaching point for hood and trunk.(1/2 inch max size). If this is used it counts as 2 of the four points.Bolts cannot exceed 1/2 inch thick. washers cannot exceed 4-inch diameter x 1/8 thick. wire or chain is allowed to secure hood closed. Must be a 12x12 hole in the hood to allow for Fire Protection. Pre-bending is allowed.
5.Bumpers must be Factory style bumpers(1980's and newer). Bumper shocks may be welded.Factory bumper brackets of shock maybe welded to end of frame(not to side) no adding metal!!!! Bumper height must be with end 18-24 inches. will be measured in the middle of the shock or attaching point.Bumper must be able to be bolted and unbolted from frame without any cutting.Bumper Hitches must be removed. NO welding on frame or body except bumpers!!!
6.Car must have a number on the door or a roof sign.Sponsors names may be any where on the car except front doors. Nothing Obscene!!!
7.Driver must where a helmet and seat belt. A fire jacket is not mandatory but preferred!
8.No Studded or Chained Tires.Tires must be round and made of rubber.Seriously.....
9.Stock fuel tank must be removed. A boat tank may be used but must be securely mounted behind the front seat and covered for safety. Max of 6 gallons of fuel.
10.Engine swaps allowed,No metal in excess to mount for the swap. Nothing to brace Frame!!!! 2 12-inch chains may be used to help secure engine.Covering distributor,Removing fan,and Hand Throttles Permitted.
11.Radiator must be in stock location. May use (2 max) ratchet straps,Wire,or Steel Strap(1 inch wide) to mount and locate radiator. No Spray Foam allowed around Radiator.
12.Car Must have working Suspension.Must have bounce ,no rigid or solid suspension.
13.Battery Must Be Relocated to passenger side area.Must be securely mounted and covered for safety.
14.Car must have factory rubber body bushings.
15. Positive traction is encouraged and rear gear ratios may be changed. NO truck rears. 5-lug Only.
16.Pitching/Tilting is allowed,but only by cutting factory tab at crush box,bending car frame the rewelding factory tabs. One Pass Only!!!
These Are your rules For this show If you have Any ?'s just send me a messege in my inbox and i will get back to you with the # to the guy to contact!! Thanks and Hope to see you there!!!
Repor
Read more: we-crash.proboards.com/index.cgi?action=display&board=southern&thread=17663#ixzz1zQRsMw3Y
1st place pays $1200
2nd place pays $600
Heats pay $300 (car count depends on how its split 2 or 3 ways)
Rules Are as Such..........
1.Car entries are to be 1980 and Newer.No Trucks.Cars are to be stock unless otherwise Noted.All Glass,Trim,Fiberglass,Plastic,and Car Interior must be Removed.
2. Doors have the option to be welded,chained,or wired shut,if welded a maximum of 12 inches in length total. If Chained or wired,a maximum of 2 places per door. If welded,Material if not to exceed 1/8 thick x 2 inch wide strap or 3/8 solid rod.
3.For Driver safety a cage is optional but is not mandatory.Cage is not to exceed a 4 point cage(Driver and Passenger door bar,Dash Bar ,and Seat bar) cage material should not be exceed 4-inch tubing or I-Beam.Cage cannot be welded or bolted to frame,only attached to the body of the car.Door bars cannot extend more than 8-inches past the "front door" jam seam toward the rear of the vehicle and cannot extend 8-inches forward "front door" jam seam. Must Be atleast 10 inches off the floor pan. A roll over bar is allowed,Must be Attached to the Cage.
4.Trunk and Hood must be open for inspection.Hood and Trunk maybe secured closed using 4 extra points.Al-thread maybe used in the front(radiator support) and rear 2 body bushings(closest to Bumper) as attaching point for hood and trunk.(1/2 inch max size). If this is used it counts as 2 of the four points.Bolts cannot exceed 1/2 inch thick. washers cannot exceed 4-inch diameter x 1/8 thick. wire or chain is allowed to secure hood closed. Must be a 12x12 hole in the hood to allow for Fire Protection. Pre-bending is allowed.
5.Bumpers must be Factory style bumpers(1980's and newer). Bumper shocks may be welded.Factory bumper brackets of shock maybe welded to end of frame(not to side) no adding metal!!!! Bumper height must be with end 18-24 inches. will be measured in the middle of the shock or attaching point.Bumper must be able to be bolted and unbolted from frame without any cutting.Bumper Hitches must be removed. NO welding on frame or body except bumpers!!!
6.Car must have a number on the door or a roof sign.Sponsors names may be any where on the car except front doors. Nothing Obscene!!!
7.Driver must where a helmet and seat belt. A fire jacket is not mandatory but preferred!
8.No Studded or Chained Tires.Tires must be round and made of rubber.Seriously.....
9.Stock fuel tank must be removed. A boat tank may be used but must be securely mounted behind the front seat and covered for safety. Max of 6 gallons of fuel.
10.Engine swaps allowed,No metal in excess to mount for the swap. Nothing to brace Frame!!!! 2 12-inch chains may be used to help secure engine.Covering distributor,Removing fan,and Hand Throttles Permitted.
11.Radiator must be in stock location. May use (2 max) ratchet straps,Wire,or Steel Strap(1 inch wide) to mount and locate radiator. No Spray Foam allowed around Radiator.
12.Car Must have working Suspension.Must have bounce ,no rigid or solid suspension.
13.Battery Must Be Relocated to passenger side area.Must be securely mounted and covered for safety.
14.Car must have factory rubber body bushings.
15. Positive traction is encouraged and rear gear ratios may be changed. NO truck rears. 5-lug Only.
16.Pitching/Tilting is allowed,but only by cutting factory tab at crush box,bending car frame the rewelding factory tabs. One Pass Only!!!
These Are your rules For this show If you have Any ?'s just send me a messege in my inbox and i will get back to you with the # to the guy to contact!! Thanks and Hope to see you there!!!
Repor
Read more: we-crash.proboards.com/index.cgi?action=display&board=southern&thread=17663#ixzz1zQRsMw3Y