|
|
Post by robbor77 on Sept 9, 2012 7:53:14 GMT -5
Hey,, Demo Derby Fans... PnP is''''''' Back "''''' the Show is called
HALLOWEEN HAVOC.... PLACE.... STERLING IL... SPEEDBOWL PARK.. DATE... OCT 27th..2012. GATES OPEN AT 12NOON.
First show Side by Side truck drags at 2pm. Demo derby Starts at 4pm. come and watch 100 cars battle for 9 thousand in PRIZE MONEY.. 10$ GRANDSTAND, 20 PIT PASS... FOR MORE INFO CALL CHARLIE @ 815-973-6356.
|
|
|
|
Post by Speed Bowl Park Sterling IL on Sept 21, 2012 9:38:33 GMT -5
Thank you Robbo for all your Support...
Here is some more info about this show..
I'm going to have 4 classes.
WELD CLASS. 100 TO ENTER. 2,500-1000-500 25 CAR ONE RUN HEAT.
WIRE CLASS 50 $ TO ENTER. 25 CAR ONE RUN HEAT, 1000-500-200
MINI CAR CLASS 50$ TO ENTER, 25 CAR HEAT. 100-500-200.
AND TRUCK CLASS.. 50$ ENTRY 25 TRUCK HEAT, 1000-500-200.
NOW IF WE SHOULD RUN OVER IN SOME CLASSES ? I WILL KICK IN MORE MONEY TO THAT CLASS..
FOR MORE INFO ON RULES CALL CHARLIE, @ 815-973-6356
|
|
|
|
Post by Speed Bowl Park Sterling IL on Sept 25, 2012 7:24:45 GMT -5
small car class, rules..
Payout for this class 1,000-500-200
this class will only have 25 cars in it. u will not have to bring any parts, just your car.
1.General rules and car preparation also apply to compacts except for the following.
2.Wheelbase is 108 inches of less with a 4 or 6 cylinder motor.
3.4x4's can be run but one drive shaft must be removed. No altering wheelbase.
4.A 2x2 1/4 inch thick piece maybe added on top side of the radiator support but must be between the two pieces of all-thread and cannot exceed the outside of the frame.
5.All frame and body seams maybe welded under the hood, firewall forward with no filler.
6.All cage rules apply with the exception that the side bars can be no longer than 72 inches.
7.One back window bar maybe ran in the, middle of the trunk seam and cannot be attached to the halo bar.
8.You will be allowed to do one of the following, not both (neither can be 12 inches behind the front of the frame):
9.Run a stock shock and bracket that cannot exceed 12 inches. If you do this the shock must be inside the bracket.
10.Run a pipe no bigger than 3 inches in diameter or a 3"x3" tube. Neither can be thicker than1/4". Neither of these may be longer than 12". If you do this option you must have a 1/2" hole drilled in your frame at the 12" point. You must also drill in your pipe or tube a 1/2" hole so we can see how thick it is also. These must be drilled before coming through inspection.
11.You may run 6 leaf springs anyway you want. Cannot double wrap the main and must be no thicker than 5/16". You may use up to 6 spring clamps. Stagger must be 2" in the back and 1" in the front.
12.You may wedge a trunk but if you do your bumper height must be a minimum of 18 inches off of the ground from the bottom of the back bumper.
13.No distributor protectors allowed..
|
|
|
|
Post by Speed Bowl Park Sterling IL on Sept 25, 2012 7:28:24 GMT -5
--------------------------------------------------------------------------------
TRUCK CLASS
Payout for this class 1,000-500-200
this class will only have 25 cars in it. u will not have to bring any parts, just your car.
THIS YEARS TRUCK DEMO CLASS IS A FULL WELD CLASS SO PLEASE CALL IF U HAVE ANY QUESTIONS..
1.Pre-derbied trucks are allowed, provided they meet all rules
2.4x4 trucks will be allowed, but must remove driveshaft to make 4x4 inoperable
3.NO midsize trucks
4.Drivers Must Wear Long Sleeve Shirt and Eye Protection
Vehicle Preparation
1.Remove all glass, chrome, plastic, moldings, headliner, dash and flammable material, A/C coolant, antifreeze, trailer hitches, and interior decking
2.Stock gas tank must be removed. A small metal tank must be mounted in rear seat area. The tank must be very secure, safe and covered. Plastic tanks are not allowed for safety reasons.
3.Electric fuel pump allowed but switch must be clearly marked on - off.
4.No more than 1 battery allowed, which must be relocated to front passenger floor, secured and covered.
5.Floor shifter allowed. Ignition and wiring modifications (hot wire) allowed.
6.Hood must have a 12"x12" minimum hole to easily extinguish fires. Extra hole(s) in hood not required if you have at least 12"x12" header holes
Frame, Body and Bumpers
1.Frame seam welding is allowed, minimal boxing of the frame rails, must be OEM 1/2 ton, 3/4 ton, or 1 ton truck frame. Frame repair due to damage or rust is allowed - repair cannot exceed 1" past rust or damage. Frame repair metal cannot be thicker than 1/4". Repairs can only be made on 1 of the 4 sides of the frame. Paint all repairs a bright color for identification. Bolting or pinning of frames is NOT allowed. Frames will be scoped.
2.No stuffing or filling of frame. Do not undercoat, paint, or put any substances in or on frame.
3.Body seam welding, bolting, or screwing is allowed. Body repair due to damage or rust is allowed - repair cannot exceed 3" past rust or damage. Body repair metal cannot be thicker than 1/8".
4.Firewall, floor pan (for shifter), wheel wells and fenders can be trimmed
5.Fenders or wheel wells may be bolted or welded. (10) bolts max. 3/8" max size
6.Doors and tailgate can be welded shut with 1/4" thick x 6" max plates or straps. A 12"x12" access hole in the trunk lid or floor is required for inspection. Plates/straps cannot go to the frame. Tops of doors can be folded over and welded. If doors are not welded shut, they must be chained/wired. Two chains/wires per window opening allowed.
7.Tailgate and hood can be secured by a max of 6 bolts each. Max of 1" diameter. Bolts can be welded or bolted to the frame. You may substitute an equivalent size piece of steel ( I.E. pipe or tube steel) and weld a bolt on the end, instead of using a long piece of threaded rod. No flat washers or plates bigger than 6"x6"x1/4". Six chains/wires can be used if bolts are not - you can use wither but only 6 methods total.
8.Body mounts may be removed. Original bolts can be replaces with up to 1" max diameter. Six (6) additional body mount bolts may be added; they must all be vertical and no longer than 10" with max diameter of 1". Any bolts holding gas tank, battery box, etc. to the frame are considered body mount bolts. No flat washers or flat plates bigger tan 6"x6"x1/4". Bolts can extend all the way through the frame but plates will need to be off for inspection.
9.Rear Suspension conversions are not allowed. No front suspension conversions unless OEM factory parts are used and mounted in OEM frame holes. Leaf spring must be NO thicker than 3/8". Springs must remain factory style for that make and model. NO FLAT SPRINGS!! Springs may be clamped. Five (5) per side. Control arms, A-arms, tie- rods, ball joints and steering joints may be modified. Max bumper height of 28” from ground to bottom of bumper. Front and back!
10.Bumpers and brackets may be interchanged from autos. Homemade brackets allowed but must be no longer or thicker than stock brackets.
11.Bumpers, shocks and brackets may be welded, bolted and chained/wired. Two piece of 4"x12"x1/4" metal may be welded or bolted to help hold the bumper on. Bumpers may be trimmed but no sharp edges.
12.Dash bar and seat cars are allowed for driver's safety. Bars may be connected to each other with door bars and may be connected to the frame (in 4 places MAX). Bars may not extend past the firewall and may not extend rearward beyond the front most part of the rear wheel well tubs. Bars may not tie into rear frame humps or drive train. Halo (rollover) bars allowed but they must remain within the safety cage area and must be vertical.
13.Driver's door window net/guard required. Windshield guard is recommended.
Engine and Drive Train
1.Any engine, transmission, rear-end combination may be used. Rear-end must be max of 8 lug automotive type. Rear-end may be welded or spooled. Rear-end may be chained/wired to frame in 2 places with bolts - not welded
2.Engine must be within 5" of original position. Engine components may be modified (fan blades, header pipes, etc.) Transmission cooler allowed, must be secure and safe. Transmission may be chained/wired in place.
3.Motor mounts may be modified to better hold engine in place but may not strengthen truck.
Miscellaneous
1.Radiator must be in stock position. No other auxiliary systems allowed. Radiator guards allowed, provided they are no thicker than 1/4" and are connected only to the radiator and sheet metal. They may not connect to the frame, bumper, or threaded rod for the hood.
2.Any type of tire or wheel may be used. Split rims must be welded solid. Wheel weights must be removed. Valve stem protectors are allowed.
3.All trucks must have number on a roof mounted sign. Choose you own number, first come first serve.
|
|
|
|
Post by crusher71 on Sept 27, 2012 0:49:21 GMT -5
HEY CHARLIE!!!!!!!!!!  |
|
|
|
Post by 73demo on Sept 27, 2012 8:17:02 GMT -5
HEY CHARLIE!!!!!!!!!! ;D so CRUSHER does this mean you will make the road trip with a car  |
|
|
|
Post by crusher71 on Sept 29, 2012 21:39:03 GMT -5
SORRY, WISH I COULD, WOULD LOVE TO RUN ONE THERE. JUST RAN A CHAIN AND GO THIS AFTERNOON AND HAD A BLAST...... I KNOW CHARLIE HAS A GOOD HEART AND LOVES THE DERBY SPORT....
|
|
|
|
Post by crusher71 on Oct 10, 2012 22:14:47 GMT -5
OUGHT TO GETTING A FEW MORE CALLS NOW CHARLIE......... |
|
|
|
Post by robbor77 on Oct 13, 2012 6:57:43 GMT -5
ANY BODY COMING BESIDES ME??  |
|
|
|
Post by Speed Bowl Park Sterling IL on Oct 16, 2012 6:25:44 GMT -5
CHECK IN FOR TRUCK DRAGS,, IS IN THE PITS @ 11AM.... Side by Side truck Drags Start at 12noon. 40$ ENTRY,it covers your pit pass 4 the entire day. Pay Back is 100$ 1st,50$- and 25$ 3rd.
Inspection FOR THE DEMO CARS WILL START AT 10AM, @ Frary Lumber & Supplys witch is
just east of the park,,, LEAVE YOUR CARS ON THE TRAILOR...
ANY QUESTIONS CALL CHARLIE @ 815-973-6356
Please pay atten,to the {Parking people), because we'll have over 100 cars for this show, and have to squezzzzzzzzzzzz u all in the pits..
One more thing, there will be someone FILMING THIS SHOW , we will have the info for u the day of the show.. These people will be onBord with PnP for Future shows..
Write a comment...
.
|
|
|
|
Post by Speed Bowl Park Sterling IL on Oct 20, 2012 6:09:58 GMT -5
Top of day to all u Demo Drivers..
This is Charlie From PnP Motorsports.
I have been getting some calls from drivers wanting me to
add a HEAVY WELD CLASS. THIS IS WHAT I'LL DO.
I WILL ADD A ONE OF THEM TO THE SHOW.
I WILL MATCH THE ENTRY MONEY. THATS 200% PAYBACK
|
|
|
|
Post by keepweldin23 on Oct 21, 2012 18:36:04 GMT -5
Charlie,
Was wondering if any core buyers will be at his show?
|
|
|
|
Post by Speed Bowl Park Sterling IL on Oct 23, 2012 5:27:31 GMT -5
i have not been asked by anyone. as of yet.
|
|
|
|
Post by 73demo on Oct 27, 2012 22:56:12 GMT -5
what a good show it was time posted was from 4 to 8 and wow ended about 8 maybe a I con can take notes on how to make a show keep going and cars a hitting and bending but then the sand baggers would not like that so the cons wont do any thing to stop there baggers the cons will still lye and steal like they did to the kid club from George Town and they will still try and con people with smoke and mirrors and tell you what ever you want to hear as long as you show up to there shows with a car or better yet they love the big scam they got going pit passes for every one ya 5 year olds are big help in the pits.
Keep it up PnP great to see your shows are back
|
|
|
|
Post by crusher71 on Oct 27, 2012 23:58:00 GMT -5
TALKED WITH CHARLIE TONIGHT AND HE SAID HE HAD 90 CARS SHOW UP....... CONGRATS ALL AROUND TO HIM FOR SHOWING THE NON-BELIEVERS THAT A NEW DERBY CAN HAVE AN OUTSTANDING CAR COUNT FOR ITS FIRST EVENT... THE CONS AT DERBY ICONS ARE NOW STARTING TO SWEAT.......SPRING EXPLOSION AND MAYHEM COUNTS WILL BE TRAGIC IN 2013. PEOPLE ARE TIRED OF THEIR LINE OF B.S. ........
|
|
